DIN En1092 Hot-dip galvanized forged steel blind plate flange sliding sleeve flange welding neck flange

AEA Blind Flanges are used to seal the end of a piping system or pressure vessel openings to prevent flow. They are commonly used for pressure testing the flow of liquid or gas through a pipe or vessel. They also allow easy access to the pipe in the event that work must be done inside the line. Blind pipe flanges are often used

Featured Products

AEA Blind Flanges are used to seal the end of a piping system or pressure vessel openings to prevent flow. They are commonly used for pressure testing the flow of liquid or gas through a pipe or vessel. They also allow easy access to the pipe in the event that work must be done inside the line. Blind pipe flanges are often used for high pressure applications.
DIN En1092 Hot Dipped Galvanized Forged Steel Blind Flange Slip on Flange Weld Neck Flange
 
RAW MATERIAL LIST
NO.Material GradeCategoryNO.Material GradeCategory
A.Cr-Mo AlloyC.Duplex
1ASTM A182 F1Cr-Mo Alloy27ASTM A182 F44Duplex SS
2ASTM A182 F5Cr-Mo Alloy28EN10222 1.4462Duplex SS
3ASTM A182 F9Cr-Mo AlloyD.Stainless Steel
4ASTM A182 F11Cr-Mo Alloy29ASTM A182 F304/F304LAustenitic SS
5ASTM A182 F22Cr-Mo Alloy30ASTM A182 F304HAustenitic SS
6ASTM A182 F91Cr-Mo Alloy31ASTM A182 F316/316LAustenitic SS
7EN10222-2 16Mo3Cr-Mo Alloy32ASTM A182 F317/317LAustenitic SS
8EN10222-2 13CrMo4-5Cr-Mo Alloy33ASTM A182 F316TiAustenitic SS
B.Carbon Steel34ASTM A182 F321Austenitic SS
9ASTM A105Carbon Steel35ASTM A182 F347/F347HAustenitic SS
10ASTM A694 F52Carbon Steel36ASTM A182 F904LSuper Austenitic SS
11ASTM A694 F60Carbon Steel37ASTM A182 F347/F347HAustenitic SS
12ASTM A694 F65Carbon Steel38EN10222-2 1.4306Austenitic SS
13ASTM A694 F70Carbon Steel39EN10222-2 1.4401Austenitic SS
14ASTM A516 GR 65Carbon Steel40EN10222 1.4404Austenitic SS
15ASTM A516 GR 70Carbon Steel41EN10222 1.4541Austenitic SS
16EN10222-2 S235JRG2Carbon Steel42EN10222 1.4571Austenitic SS
17EN10222-2 P250GHCarbon Steel43EN10222 1.4539Super Austenitic SS
18EN10222-2 P280GHCarbon SteelAlloy
19EN10222-2 P355QHCarbon Steel44B564 UNS N08020Ni-Alloy
20ASTM A516 GR 60Low Temp CS45B564 UNS N04400Ni-Alloy
21ASTM A350 LF2Low Temp CS46B564 UNS N6600Ni-Alloy
22ASTM A350 LF3Low Temp CS47B564 UNS N06625Ni-Alloy
23ASTM A350 LF6Low Temp CS48B564 UNS N08367Ni-Alloy
C.Duplex49B564 UNS N08800Ni-Alloy
24ASTM A182 F51Duplex SS50B564 UNS N08825Ni-Alloy
25ASTM A182 F60Duplex SS51B564 UNS N10276Ni-Alloy
26ASTM A182 F53Duplex SS52ASTMB171 UNS C71520Cu-Alloy


DIN En1092 Hot Dipped Galvanized Forged Steel Blind Flange Slip on Flange Weld Neck Flange


Specifications :

Flange Type:                                   
Weld Neck, Slip On, Blind, Plate, Thread, Socket Weld, Lap Joint, Ring Joint, Orifice Flange, Spectacle Blind, Paddle Spacer and Blank Flange, Figure 8 Flange, etc;
                                    
Face: Raised Face (RF),Flat Face(FF), Ring Joint (RTJ)  
                                    
Material:                                  
Carbon Steel:   Q235,20#,A105, ST37.2,C22.8, S235JR,P250GH,A350 LF1,LF2 CL1/CL2 LF3 CL1/CL2, ASTM A694 F42,F46,F48,F50,F52,F56,F60,F65,F70
Stainless Steel: A182 F304/304L, F316/316L, F316H,F316Ti,F321,F44(UNS S31254)
Ally Steel:          A182 F1,F5/a,F9,F11,F12,F22,F91  
Duplex Steel:    A182 F51/UNS S31803,F53/UNS S32750 F55/UNS S3260
Special Alloy:   ,C95400,C95500,C95800,Monel400,Inconel 600, Inconel 625, Inconel 800, Inconel 825
                                    
Standard:                                
ASME: ANSI/ASME B 16.5,ASME B16.36,ASME B16.47 Series A(MSS SP-44);ASME B16.47 Series B(API 605),AWWA C207
DIN:          Plate(DIN2573,2576,2502),Blind(DIN2527),Loose(DIN2641-2676),Welding-Neck (DIN2627-2638), Threaded (DIN2565 2566 2567) ,Slip-On (DIN86029 86030)
EN:  EN1092-1                           
JIS:  JIS B2220                          
UNI:          UNI2253-2278,UNI6083,UNI6084,UNI2280,UNI2281-2286, UNI6091-6097
GOST: GOST12820-80, GOST12821-80 
BS: BS 4504,BS10-1962,BS3293-1960 
                                    
Pressure:                                 
ANSI:Class 75, Class 150, Class 300, Class 600, Class 900, Class 1500, Class 2500
DIN:PN 6,PN 10,PN 16,PN 25,PN 40                 
EN:PN 6,PN 10,PN 16,PN 25,PN 40               
JIS:1K,2K,5K,10K,16K,20K,30K,40K,63K ;                  
GOST:PN 6,PN 10,PN 16,PN 25,PN 40,PN63,PN100,PN160                   
BS:TABLE D E                                    

 Machining Tolerance:  From 0.005mm-0.01mm-0.1mm As Standard.

Machined Surface Quality: Ra 0.8-Ra3.2 according to customer requirements

Production Process:
Forging-Heat Treatment-Machining (rough machining and finish machining)-Drilling-Inspect-Stamp-Packing

Heat Treatment: Solution, N+T (Normalizing + Tempering), Q+T (Quenching + Tempering)


Surface Treatment                
Anti-rust Oil, Transparent/Yellow/Black Anti-rust Paint,Zinc,Hot dipped Galvanized.                                   
Usage: 
Oil Field, Offshore, Water System, Shipbuilding, Natural Gas, Electric Power, Pipe Projects etc.



 
Table ANSI, ASME, ASA, B16.5 150lb/sq.in. Blind Flange
øDbgkHoleslKg.
1/2"88,911,134,960,3415,90,400
3/4"98,412,742,969,8415,90,700
1"107,914,350,879,4415,90,900
1 1/4"117,515,963,588,9415,91,300
1 1/2"127,017,573,098,4415,91,600
2"152,419,092,1120,6419,02,600
2 1/2"177,822,2104,8139,4419,04,100
3"190,523,8127,0152,4419,05,000
3 1/2"215,923,8139,7177,8819,06,400
4"228,623,8157,2190,5819,07,100
5"254,023,8185,7215,9822,29,000
6"279,425,4215,9241,3822,211,800
8"342,928,6269,9298,4822,221,000
10"406,430,2323,4361,91225,430,000
12"482,631,7381,0431,81225,445,000
14"533,434,9412,7476,21228,659,000
16"596,936,5469,9539,91628,679,000
18"635,039,7533,4577,81631,797,000
20"698,542,9584,2635,02031,7124,000
22"749,346,0641,2692,12034,9151,000
24"812,847,6692,1749,32034,9188,000
NOTE:
1. Class 150 flanges except Lap Joint will be furnished with 0.06 (1.6mm) raised face, which is included in 'Thickness' (C) and 'Length through Hub' (Y1), (Y3).
2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees.
3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub.
4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C).
5. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer's option.
 
Table ANSI, ASME, ASA, B16.5 300lb/sq.in. Blind Flange
øDbgkHoleslKg.
1/2"95,214,334,966,7415,90,700
3/4"117,515,942,982,5419,01,200
1"123,817,550,888,9419,01,500
1 1/4"133,319,063,598,4419,02,000
1 1/2"155,620,673,0114,3422,22,900
2"165,122,292,1127,0819,03,400
2 1/2"190,525,4104,8149,2822,25,100
3"209,528,6127,0168,3822,27,000
3 1/2"228,630,2139,7184,1822,28,900
4"254,031,7157,2200,0822,211,800
5"279,434,9185,7234,9822,215,500
6"317,536,5215,9269,91222,221,300
8"381,041,3269,9330,21225,435,200
10"444,547,6323,8387,31628,657,000
12"520,750,8381,0450,81631,782,000
14"584,254,0412,7514,32031,7106,000
16"647,757,1469,9571,52034,9140,000
18"711,260,3533,4628,62434,9178,000
20"774,763,5584,2685,82434,9223,000
22"838,266,7641,2742,92441,3270,000
24"914,469,8692,1812,82441,3345,000
NOTE:
1. Class 300 flanges except Lap Joint will be furnished with 0.06 (1.6mm) raised face, which is included in 'Thickness' (C) and 'Length through Hub' (Y1), (Y3).
2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees.
3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub.
4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C).
5. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer's option.
 
Table ANSI, ASME, ASA, B16.5 600lb/sq.in. Blind Flange
øDbgkHoleslKg.
1/2"95,214,334,966,7415,90,700
3/4"117,515,942,982,5419,01,200
1"123,817,550,888,9419,01,500
1 1/4"133,320,663,598,4419,02,000
1 1/2"155,622,273,0114,3422,23,200
2"165,125,492,1127,0819,04,300
2 1/2"190,528,6104,8149,2822,26,000
3"209,531,7127,0168,3822,28,000
3 1/2"228,634,9139,7184,1825,410,500
4"273,038,1157,2215,9825,418,000
5"330,244,4185,7266,7828,628,500
6"355,647,6215,9292,11228,635,500
8"419,155,6269,9349,21231,758,000
10"508,063,5323,8431,81634,998,000
12"558,866,7381,0488,92034,9125,000
14"603,269,8412,7527,02038,1151,000
16"685,876,2469,9603,22041,3215,000
18"742,982,5533,4654,02044,4287,000
20"812,888,9584,2723,92444,4366,000
22"869,995,2641,2777,92447,6437,000
24"939,8101,6692,1838,22450,8532,000
NOTE:
1. Class 600 flanges except Lap Joint will be furnished with 0.25 (6.35mm) raised face, which is not included in 'Thickness' (C) and 'Length through Hub' (Y1), (Y3).
2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees.
3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub.
4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C).
5. Dimensions of sizes 1/2 through 3 1/2 are the same as for Class 400 Flanges.
6. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer's option.
 
Production Capacity & Purchase Details
  
1.Supply Flange Dimension DN15 - DN600 (1/2" - 24") for Blank Flange, Forged Flange.
2.Flange Material Carbon Steel: ASTM A105, A181, A350 LF1, A350LF2, A350LF3, A36, A234 WPB, Q235B, 20#, 20Mn.
3.Flange Material Stainless Steel: ASTM A182 F304, F304L, F316, F316L, F321 etc.
4.Flange Anti Rust: Anti Rust Oil, Black Paint, Yellow Paint Coating, Hot Dipped Galvanized, Cold Galvanized etc.
5.Flange Monthly Output: 3000 tons per Month.
6.Flange Delivery Terms: CIF, CFR, FOB, EXW, transport by sea, by air, by express DHL, FedEx, TNT, EMS.
7.Flange Payment Terms: Wire Transfer (T/T), Irrevocable L/C at Sight etc.
8.Flange Minimum Order Quantity (MOQ): 1Ton or 100Pcs per size.
9.Quality Guarantee: EN10204 3.1 Certificate, Mill Certificate, Third Party Inspection, Free Replacement Service.
10.Find More Requirements In Flanges Market.

 





DIN En1092 Hot Dipped Galvanized Forged Steel Blind Flange Slip on Flange Weld Neck Flange

 

Contact us

Please feel free to give your inquiry in the form below We will reply you in 24 hours